Clothing inspection

Full inspection of e-commerce clothing is generally carried out in the factory. After the clothing is produced, inspectors from a third-party clothing quality inspection company will conduct a full inspection before packing to ensure that the clothing 100% meets the customer's quality requirements.

1. Communicate with the factory about the product completion status 1-2 days in advance and arrange a full inspection time to ensure that there is time for repairs when problems arise. The location needs to be the factory inspection;
2. After the product tag is completed, the inspectors will conduct the first inspection of all the garments, checking the quantity, tag, washing label, trademark, size label, style, quality, craftsmanship, symmetrical parts, and firmness of the products;
3. Take size measurements and conduct random inspections of each size;
4. Pick out defective products, count them, and classify them according to defects;
5. The factory returns defective products for repair;
6. Conduct a second quality inspection on defective products that have been repaired by the factory to check whether the defective products are qualified;
7. Repeat steps 3, 4, and 5 above until all products are 100% qualified;
8. Issue inspection report.

1. Clothing style inspection:

- Whether the collar is flat, the sleeves, collar and collar should be round, with clear lines and symmetry on both sides;

- Fabric appearance, yarn deviation, color difference, coarse yarn, fabric quality, and damage.

2. Clothing quality inspection symmetry inspection:

- The collar, sleeves and shoulder bones of the garment should be aligned;

- Front pocket height, size, distance, collar point size, front and back lapels, left and right lapels, and whether contrasting colors are relative;

-Whether the width of the two arms and the two collars are consistent, the length of the two sleeves, and the size of the cuffs.

3. Garment quality inspection and workmanship inspection:

- The threads of each part should be flat and firm, without skipped threads, broken threads, floating threads, too many threads and not appearing in conspicuous places, the stitch distance should not be too sparse or too dense, and the bottom thread should be of appropriate tightness;

-Sewing gestures and movements should be even to avoid tightness and wrinkles;

- Parts to pay attention to: collar, tube, clip, mountain stripe pockets, hem, cuffs;

- The placket should be straight, the left and right hems should be the same length, without wrinkles. Round ones should be round and smooth, square ones should be square, and the left and right collar gaps should be the same;

- The zipper on the front placket should be evenly spaced and appropriately tight to avoid wavy formation. Be careful not to fall in the middle of the front. The zipper width should be symmetrical on both sides, and the hem of the shirt should be carefully shaped;

- The shoulder seams, sleeves, collars and waists should be appropriate, the collar floss should be naturally flat, and the collar should be appropriately tight after being turned up, without any bottom exposure;

-The pocket cover should match the front body, the fabric in the pocket cover should be of appropriate tightness and should not be warped, there should be no missed stitches or skipped stitches in the pocket, the pocket lining should be firm and clean, and the seal should have no holes; 8. The lining of the shirt should not be exposed (shirt hem, cuffs), the cotton should not be exposed, check whether the lining has enough margin, whether there are cracks, whether the stitches are too sparse, whether the surface fabrics of each part fit together smoothly, and whether there is any tightness.

- The Velcro cannot be misplaced, and the heavy and missing threads, as well as the upper and lower sizes must be consistent;

- The positioning of the phoenix eye should be accurate, the operation should be neat and without any hair, the needle and button thread should not be too tight or too loose, the button should be in place and the tightness should be appropriate;

- The size and location of the dates must meet the design requirements, and trailers are not allowed;

-The wool fabrics should be consistent in both forward and reverse directions.

4. Dimensional inspection:

Measure the dimensions strictly according to the dimension table required by the order.

5. Clothing quality inspection and stain inspection

- All parts should be flat, without yellowing, aurora, water stains, or discoloration;

- Keep all parts clean, free of dirt and hair;

-Excellent effect, soft touch, no yellow spots or water stains.

1. Appearance inspection:

- Thick and thin yarn, color difference, stains, yarn movement, damage, yarn snagging, dark and horizontal, fuzzy, and hand feel;

- The collar should be flat and the collar clip should be round;

- Fabric quality inspection: shrinkage, color loss, flat collar, rib tensioner color matching and texture.

2. Dimension inspection: Strictly follow the dimension table.

3. Symmetry test:

Shirt

- Collar tip size, whether the collar bones are relative;

-The width of the two arms and two clamps;

-The length of the sleeves and the width of the cuffs;

-The sides are short and the feet are long.

pants

- The length and width of the trouser legs and the width of the trouser legs

- The height of the left and right pockets, the size of the pocket opening, and the length of the left and right sides of the back pocket

4. Workmanship inspection:

Shirt

- The lines of each part should be straight, neat and firm, with appropriate tightness, and no floating, broken or skipped lines. The number of wires should not be too large and should not appear in conspicuous positions, and the stitch distance should not be too sparse or too dense;

- The collar and clipping gestures should be even, avoiding too much space in the collar and clipping ring;

- Common defects of lapel collar: crooked collar, exposed bottom collar, loose collar edge, uneven collar surface, high and low collar mouth, large and small collar tip;

Common defects of round collar: skewed collar edges, wavy collar opening, exposed collar bones;

-The top of the clamp should be straight and without corners;

- The bag mouth should be straight and the bag mouth should be clean and cut

- The extra stoppers on the four legs should be trimmed

- The sides of the shirt should not be flared, and the forks should not be high or low;

- The stripes should be of uneven thickness, and should not be too many or too tight so as to bind the fabric of the shirt;

- Don’t have too many joints in the thread, and pay attention to trimming the thread ends;

- The bottom line should be tight enough, and all bone positions should be wrinkle-free, especially the collar, gusset, and leg circumference.

-The buttonhole must be positioned accurately, the cut must be clean and without hair, the buttonhole line must be smooth and without loose edges, and it must not bulge. The button position must be accurate, and the button line must not be too loose or too long.

pants

- Pay attention to the workmanship of the back pocket. It should not be skewed and the pocket opening should be straight;

- The waistband should be parallel, not bent, and not uneven in width;

- The parts are ironed and flat, without yellowing, laser stains, water stains, dirt, etc.;

-Clear all thread ends thoroughly.

1. Modeling inspection

-The lines of the shirt are clear, the collar is flat, the collar and collar are round, the bottom edge of the hem is straight, the lines of the pants are smooth, the trouser legs are straight, and the front and back waves are straight.

2. Fabric appearance:

Coarse yarn, yarn deviation, breakage, dark horizontal color difference, water washing marks, uneven washing, white and yellow spots, and stains.

3. Symmetry test

Shirt

- The left and right collar sizes, collar circles, collarbones, and sleeve caps should be aligned;

-The length and size of the sleeves, the length and width of the cuffs;

- Bag cover, bag opening size, height, distance, rib height, left and right bone fracture positions;

- The length of the placket and the degree of the hem;

- The width of the two arms and two clamps

pants

- The length, width, and size of the two trouser legs, the waistband should be three pairs, and the side bones should be four years old;

- Front, back, left, right, height and size of spleen bag;

- Ear position and length;

1. Appearance inspection

- Coarse and fine hair, flying hair, pilling, snake-shaped hair, uneven mixed color, missed stitches, loose and not firm enough shirt body, not soft enough after washing, white marks (uneven dyeing), and stains.

2. Dimensional inspection

Follow the size chart strictly.

3. Symmetry test

- Collar tip size, whether the collar bones are relative;

- Width of arms and legs;

- The length of the sleeves and the width of the cuffs

4. Manual inspection

- Common defects of lapel styles: yarn is coming loose at the neckline, the collar is too wide, the placket is twisted or skewed, and the bottom tube is exposed;

-Common defects of bottle neck style: the neckline is too loose and flared, the neckline is too tight;

- Common defects of other styles: corners of the top are raised, the base of the shirt is too tight, the stitching of the stitching is too straight, the shirt bottom is wavy, and the side bones on both sides are not straight.

5. Ironing inspection

- All parts are ironed and flat, without yellowing, water stains, or dirt;

-No plate agglomeration, and thread ends must be completely removed.

1. Appearance inspection:

- Thick yarn, yarn slipping, flying yarn, dark horizontal, white marks, damage, color difference, stains

2. Dimensional inspection:

Follow the size chart strictly.

3. Symmetry test:

- Collar tip size, whether collar bones are relative;

-The width of the two arms and two clamps;

- length of sleeves, width of cuffs, distance between sleeve pleats, length of sleeve forks, and height of sleeve cuffs;

-Height of the two sides of the pole;

-Pocket size, height;

-The placket is long and the stripes on the left and right are symmetrical.

4. Workmanship inspection:

- Each part of the line should be straight and tight, without floating, skipped or broken lines. There should not be too many wires and they should not appear in conspicuous positions. The stitches should not be too sparse or too dense, in accordance with the regulations;

- The collar tip should be close fitting, the collar surface should not bulge, the collar tip should not be broken, and the collar hem should not be exposed. Pay attention to whether the bottom line of the collar is exposed, the hem should be neat, the collar surface should be appropriately tight and not warped, and the collar bottom should not be exposed;

- The placket should be straight and flat, the side seams should be straight, the tightness should be appropriate, and the width should be consistent;

- The inner stop of the bag should be cleanly cut, the bag mouth should be straight, the bag corners should be rounded, and the seal size should be consistent and firm;

- The hem of the shirt should not be twisted or curled outwards, the right-angle hem should be straight, and the angle of the round hem should be consistent;

- The upper and lower threads should be appropriately tight to avoid wrinkles (the areas prone to wrinkles include collar edge, placket, clip, sleeve bottom, side bone, sleeve fork, etc.);

- The collar and the clip should be evenly arranged to avoid too much space (the main parts are: collar, cuffs, clip ring, etc.);

- The buttonhole should be positioned accurately, cut neatly and without hair, the size should match the button, the button position should be accurate (especially the collar tip), and the button thread should not be too loose or too long;

- The size, length and position of the picked dates must meet the requirements;

-Main parts of matching stripes and grids: left and right panels are opposite to the placket, pocket panels are opposite to shirt panels, front and back panels are opposite, left and right collar tips, sleeve panels, and sleeve forks are opposite;

-The forward and reverse rough surfaces of the entire piece are consistent in the forward direction.

5. Ironing inspection:

- Iron the clothes flat without any yellowing, marks, water stains, dirt, etc.;

-Ironing important parts: collar, sleeves, placket;

-Thread ends must be completely removed;

- Pay attention to the penetration of glue.